Dc To Dc Converter

This is a 600W boost constant current module, non-isolated, constant current range is related to input and output voltage and load. This DC boost voltage converter input 8-16V, 600W 16A Boost power module output 12-60V, large adjustable range for various electronics. This boost power converter with large heat sink, cool down fast and allow to work in lower temperature, work much more stable, Boost power supply module with LED instruction light, clearly shown working condition. Adjustable dc boost converter, easily adjust voltage and amperage by screwing CC and CV, Boost regulator module with solder-less terminals, convenient to connect with wire and need less assists.

• Module Properties: non-isolated step-up module (BOOST)
• Input Voltage: two input voltage ranges selectable (selectable with jumper on board)
  • 8-16V input ( In this input mode, please do not over-voltage input, otherwise it will burn module)
  • 12-60V input(default)
• Input Current: 16A (MAX) Please enhance heat dissipation when current over than 10A
• Static Current: 15mA (12V to 20V. The output voltage increase, the static current will increase a little)
• Output Voltage: 12-80V (continuously adjustable) ( the default output about 19V )
• Output Current: 12A MAX, if over 10A please enhance heat dissipation ( the higher the dropout voltage, the smaller the current )
• Constant Current Range: 0.1-12A
• Output Power: = input voltage * 10A, such as: input 12V * 10A = 120W, input 24V * 10A = 240W, Input 36V * 10A = 360W, input 48V * 10A = 480W, input 60V * 10A = 600W. If you need more high-power, two modules can be used in parallel , for example if you need 15A output, then connect two modules in parallel ,the current of each module set to 8A then is OK.
• Operating Temperature: -40°C to +85°C ( if temperature too high , please enhance heat dissipation)
• Operating Frequency: 150KHz
• Conversion Efficiency: up to 95% ( affected by input voltage, output volage, current and dropout voltage )
• Operating Ripple: about 100mV
• Load Regulation Rate: about 0.2%
• Voltage Regulation Rate: about 2%
• Overcurrent Protection: Yes ( input exceeds 17A, automatically reduces the output voltage , maybe have errors)
• Short-circuit Protection: Yes (input with 20A fuse) double circuit protection, more safe.
• Input Reverse Polarity Protection: No , ( if necessary , input add one diode in series)
• Output Prevent Backflow: Yes, no need to add prevent backflow diode for charging .

• DC boost voltage converter input 8-16V, 600W 16A Boost power module output 12-60V, large adjustable range for various electronics.
• Boost power converter with large heat sink, cool down fast and allow to work in lower temperature, work much more stable, Boost power supply module with LED instruction light, clearly shown working condition.
• Adjustable dc boost converter, easily adjust voltage and amperage by screwing CC and CV, Boost regulator module with solder-less terminals, convenient to connect with wire and need less assists.
• High efficient step up voltage regulator, 95% conversion efficiency and low heat generated, DC boost step up converter with 20A short circus protection.
• Boost voltage regulator versatile to charge your electronics and lithium battery with suitable voltage and amperage, drive high-power LED lights, Boost voltage stabilizer also ideal to DIY high-power power bank, solar resource voltage stabilizer and more.

• Adjust CV potentiometer, according to your battery or LED, set the output voltage value to your need.
•  
•  

• Delivery Time: 3-5
• Packaging Details: 1 x DC Boost Converter, 600W 12A DC-DC Step Up Converter Board 8-16V 12V 24V to 12-60V 48V Voltage Regulator Booster Module

The 300W 20A DC-DC Step-down Adjustable Constant Current Module can be used to get adjustable output voltage ranges from 1.2V to 36V. The module provides a wide range of current output up to 20 A. With the heat sink mounted it can easily manage to run high power applications continuously (provided that for continuous high power output you need to use a cooling fan on the heat sink).

The Module is made from a dedicated benchmark IC and high-precision current sensing resistor, proving a more stable constant current, (when 20°C to 100°C constant current 1A, temperature drift less than 1%); and therefore it is particularly most suitable for LED driver applications. The output current of the module can be raised up to 20A(for continuous use it is recommended up to 15A with an additional cooling fan).

To enhance the stabilization in output voltage has six high-frequency capacitance which gives the lower output ripple. Double heat sink design provides easy and fast heat dissipation. MOS Schottky diode independent heat sink, which heat dissipation is good, and won’t affect each other. Also using large size Sendust Core and double pure copper wiring, improve working efficiency, reduce fever.

The module has onboard 3296 multiturn potentiometers for high accuracy voltage and current regulation to provide good stability. As voltage and current are adjustable, it gives very easy to use at multiple Application such as battery charging, LED Driver power supply, Vehicle Power Supply, etc which makes the module Multipurposeand hence this module is always in demand from our maker because of its wide range of application and low cost.

Applications:

1. High-power LED driver.
2. Lithium battery(or lead accumulator) charge.
3. Vehicle-mounted power supply.
4. Low voltage system power supply.
5. 6V, 12V, 14V, 24V battery charge.
6. On-board laptop power supply.
7. regulated power supply.
8.Low voltage power supply system.

• Item Code: RS1831
• Production Capacity: 1000
• Delivery Time: 3 to 4 days
• Packaging Details: Package Included: 1 x 300W DC Buck Converter Power Module Output Adjustable 20A Max DC-DC 6-40V Step Down to 1.2-36V

This versatile DC-DC boost power supply/converter module steps up any input voltage from 10V to 32V to any output voltage from 12V to 35V at up to 150W output power and 6A current. This 150W DC-DC Boost Converter 10-32V to 12-35V 6A Step-Up Adjustable Power Supply is well into the heavy-duty end of the spectrum @ 150W; as you can tell by the huge toroidal inductor and dual heatsinks. It is especially useful for automotive 12V applications, where standard 12V battery power can be boosted to 19V for use as a laptop computer power supply, or to 18V or 24V for other applications requiring higher voltages.
Please note there is no reverse polarity protection. A series diode is recommended. For high loads this might not be an option, so be cautious of the input polarity or you might fry the module!

• Input Voltage: 10 to 32V
• Input Current: 10A
• Output Voltage: 12 to 35A
• Max. Output Current: 6A
• Output Power: 100W
• Conversion Efficiency: 94%
• Operating Temperature: -40 to 90°C
• No-Load Current: 25mA

• The non-isolated step-up power conversion module
• Onboard LED illuminates when the voltage is applied to the module
• Equips Multi-turn Potentiometer.
• Easy to drive 65W 90W dual-core notebook.
• The output voltage is continuously adjustable on OUT+ and OUT- screw terminals (Output voltage must be greater than input voltage)

• DIY adjustable output vehicle power supply. Provide 12V input, the output voltage can be continuously adjusted from 14V to 35V (output voltage cannot be lower than the input voltage).
• Universal car laptop power supply. Provide 12V input, the output voltage is adjustable to your notebook to work. Can easily drive dual-core or quad-core notebooks at 19V and up to 6A output current.
• Boost Charger, to convert your car’s 12V power to greater than 12V, such as 18V or 24V
• Power supply for your electronic devices, as long as the voltage is adjusted to the voltage and does not exceed the module’s rated current.

Note:

• Set the output voltage to the desired level using a voltmeter before connecting it to your equipment or load.
• Short circuit protection: None, please use caution to protect the module from overcurrent
• Input reverse polarity protection: None, please use a diode in series with the input to protect against input reverse polarity

1 x 150W DC-DC Boost Converter 10-32V to 12-35V 6A Step-Up Adjustable Power Supply

• Item Code: NA065
• Production Capacity: 1000
• Delivery Time: 3 T0 4 DAYS
• Packaging Details: Package Includes: 1 x 150W DC-DC Boost Converter 10-32V to 12-35V 6A Step-Up Adjustable Power Supply